Home / Shop/ DGZ · Double threaded screw for insulation
DGZ · Double threaded screw for insulation
Supplied to order

Rothoblaas

DGZ · Double threaded screw for insulation

Product code: DGZ7220
Holz Technic code: DWZ7220
£55.83 ex VAT · 50 per box
£67.00 inc VAT
£1.12 per unit
Total: £55.83 ex VAT
Want this kept in UK stock for fast delivery? Tell us. We stock more of what customers ask for. No obligation to buy; we'll let you know when it's on the shelf.
Request this in UK stock
Delivery and returns
Delivery sorted in the basket
One clear price · FREE over £500.
FREE delivery over £500
Tracked delivery UK wide.
VAT invoice with every order
Full VAT documentation for your records
14 days to cancel after delivery
Eligible personal purchases · Personal policy · Business policy

DGZ is the Rothoblaas double threaded insulation screw, certified under ETA-11/0030, fixing counter battens and façade battens through the insulation and holding them clear of the structure behind.

The screw carries the batten load back to the rafter, joist or panel through the insulation, without a bracket or secondary joist crossing the layer. ETA-11/0030 covers it in solid timber, glulam, CLT, solid wood panel and LVL, in hard, soft and façade insulation, at 60° or 90°. Design is to EN 1995-1-1 and the UK National Annex.

Key features

  • Certified in non-pre-drilled LVL, the highest withdrawal case on the sheet, at fax,k 15.0 N/mm², ρa 500 kg/m³, characteristic density 410 to 550 kg/m³
  • Also covered in solid timber, glulam, CLT and solid wood panel
  • Double thread with a 3 THORNS tip, 100 mm point side and 60 mm head side, which is what allows the tight minimum spacings below
  • Thirteen lengths, Ø7 from 220 to 380 mm and Ø9 from 240 to 520 mm
  • Cylindrical head, Ø9.50 mm at Ø7 and Ø11.50 mm at Ø9, seated inside the batten
  • Certified for hard, soft and façade insulation, fixed at 60° or 90°, both tabulated in the ETA
  • TX30 on Ø7 and TX40 on Ø9, bit included in every box

Thermal bridging

Fixing the insulation continuously, rather than interrupting it with timber counter-joists, was calculated to improve the U-value of the roof build-up by 10 to 15%. The calculation was carried out by EURAC Research as part of the MEZeroE project, funded by the European Union's Horizon 2020 programme under grant agreement No 953157. It compares a continuous insulation package against one interrupted by secondary joists; it is a calculation, not a site measurement, and the result for any specific roof depends on that roof's build-up.

That benefit depends on restraint. The datasheet is explicit that excessive anchoring or incorrect arrangements should be avoided in order not to compromise the thermal performance of the package. More fixings than the design calls for works against the reason for choosing this detail.

Minimum spacings

The 3 THORNS tip is what buys the tight spacings. They are independent of insertion angle and of grain angle.

  • Between screws, a1 and a2: 5·d, so 35 mm at Ø7 and 45 mm at Ø9
  • To end grain, a1,CG: 10·d, so 70 mm at Ø7 and 90 mm at Ø9
  • To the edge, a2,CG: 4·d, so 28 mm at Ø7 and 36 mm at Ø9

These hold only in members of at least 12·d thickness, 84 mm at Ø7 and 108 mm at Ø9, and at least 8·d width or 60 mm, whichever is greater. The datasheet does not print that precondition next to the spacings, so check the member before you rely on them.

Before you fix

  • Check the tip cannot break through the underside of the member. This is the most common error on long insulation screws
  • Batten minimums are not optional: 50/30 mm base and height at Ø7, 60/40 mm at Ø9
  • Pre-drilling is required above 550 kg/m³ characteristic density. Note that pre-drilling LVL puts you outside the 15.0 N/mm² case above
  • Electrogalvanised zinc at minimum 5 µm, so service class 1 and 2 only, C2 atmospheric and T2 wood corrosivity. Not for exterior or coastal exposure

The same screw, two code ranges. DGZ and DWZ are the same Rothoblaas screw under two codes: DGZ is the designation used in ETA-11/0030, DWZ is the Holz Technic code. Same manufacturer, same geometry, same approvals. The range here is the wider one, running to 520 mm at Ø9 where DWZ stops at 400 mm, and the DWZ selection table is this same table narrowed to the stocked lengths, so some deeper cells are blank there. For deeper build-ups, this is the page. The screw is also certified in flange-head (DGT) and countersunk-head (DGS) versions, which we do not stock. An EVO version with a Zn-Al flake coating is available on request for service class 3 applications.

Design and specification support

Rothoblaas MyProject is a free calculation tool that produces a fastening calculation report for this screw. It is a design aid for the specifier. It does not replace the structural design of the roof, and the connection must still be checked and signed off by the project's structural engineer. See also our guide to Eurocode 5 timber design, our structural engineering support, and the full structural timber screw range.

Common questions

Does a larger diameter mean fewer fixings? Rothoblaas's own worked example on the datasheet runs both diameters over the same roof: GL24h 120x160 joists at 0.70 m centres, 20 mm planking, 160 mm soft insulation at σ(10%) 0.03 N/mm², C24 60x40 battens, 30% pitch, 1.70 kN/m² snow. It resolves to 324 screws at Ø7 or 252 at Ø9. That is an illustration from one build-up, not a sizing rule. The number for your roof is your engineer's.

Why does the ETA give two different fax,k values? Because withdrawal depends on the timber. In solid timber, glulam, CLT and solid wood panel, fax,k is 11.7 N/mm² at ρa 350 kg/m³ with characteristic density up to 440 kg/m³. In non-pre-drilled LVL at ρa 500 kg/m³ and characteristic density 410 to 550 kg/m³ it rises to 15.0 N/mm². Pre-drill the LVL and the higher figure no longer applies.

Price shown is per box of 50 pieces. See the table below for codes, lengths and pack prices.

Material
Carbon steel
Coating
Electrogalvanised zinc, minimum 5 µm
Head type
Cylindrical head
Head diameter
Ø9.50 mm (Ø7) · Ø11.50 mm (Ø9)
Thread
Double thread, 3 THORNS tip
Thread length
b 100 mm point side · b2 60 mm head side
Drive
TX30 (Ø7) · TX40 (Ø9), bit included
Diameters
Ø7 mm · Ø9 mm
Lengths
220, 260, 300, 340, 380 mm (Ø7) · 240, 280, 320, 360, 400, 440, 480, 520 mm (Ø9)
Service class
Service class 1 and 2 (EN 1995-1-1)
Atmospheric corrosivity
C2
Wood corrosivity
T2
Characteristic tensile strength ftens,k
15.4 kN (Ø7) · 25.4 kN (Ø9)
Withdrawal parameter fax,k, solid timber
11.7 N/mm² at ρa 350 kg/m³, characteristic density up to 440 kg/m³, in solid timber, glulam, CLT and solid wood panel
Withdrawal parameter fax,k, LVL
15.0 N/mm² at ρa 500 kg/m³, characteristic density 410 to 550 kg/m³, non-pre-drilled LVL only
Head pull-through fhead,k
10.5 N/mm² at ρa 350 kg/m³, softwood and wood-based panels over 20 mm
Yield moment My,k
14.2 Nm (Ø7) · 27.2 Nm (Ø9)
Minimum batten size
50/30 mm base/height (Ø7) · 60/40 mm (Ø9)
Certification
CE marked to ETA-11/0030 (ETA-Danmark, 20 August 2025, EAD 130118-01-0603) · UKCA marked to UKTA-083622/6195
Design code
EN 1995-1-1 (Eurocode 5) and the UK National Annex
Also sold as
DWZ, the Holz Technic code for the same screw
Also certified as
DGT flange head · DGS countersunk head (not stocked)
Pack
50 pieces per box, TX bit included
Brand
Rothoblaas
Over-rafter warm roof insulationCounter batten fixing through insulationVentilated façadesWarm roofs on CLT and glulamLVL and engineered timber structuresHard insulation boardsSoft insulationFaçade insulationFixing at 60° or 90°Timber-to-timber
Technical datasheet
PDF · Opens in new tab · Download from viewer
View datasheet
Working out a whole connection? Get exact box quantities with our Fastener Calculator. Open calculator

Choose sizes and quantities

Add several sizes to your basket in one go.

Size / product codeSold asPrice ex VATAvailabilityQuantity
7 mm · min. batten 50/30 mm / 220 mmDGZ7220 Box of 50 £55.83per box Supplied to order
Boxes
7 mm · min. batten 50/30 mm / 260 mmDGZ7260 Box of 50 £76.00per box Supplied to order
Boxes
7 mm · min. batten 50/30 mm / 300 mmDGZ7300 Box of 50 £81.56per box Supplied to order
Boxes
7 mm · min. batten 50/30 mm / 340 mmDGZ7340 Box of 50 £94.85per box Supplied to order
Boxes
7 mm · min. batten 50/30 mm / 380 mmDGZ7380 Box of 50 £110.94per box Supplied to order
Boxes
9 mm · min. batten 60/40 mm / 240 mmDGZ9240 Box of 50 £88.26per box Supplied to order
Boxes
9 mm · min. batten 60/40 mm / 280 mmDGZ9280 Box of 50 £112.26per box Supplied to order
Boxes
9 mm · min. batten 60/40 mm / 320 mmDGZ9320 Box of 50 £122.40per box Supplied to order
Boxes
9 mm · min. batten 60/40 mm / 360 mmDGZ9360 Box of 50 £141.60per box Supplied to order
Boxes
9 mm · min. batten 60/40 mm / 400 mmDGZ9400 Box of 50 £163.47per box Supplied to order
Boxes
9 mm · min. batten 60/40 mm / 440 mmDGZ9440 Box of 50 £203.46per box Supplied to order
Boxes
9 mm · min. batten 60/40 mm / 480 mmDGZ9480 Box of 50 £244.00per box Supplied to order
Boxes
9 mm · min. batten 60/40 mm / 520 mmDGZ9520 Box of 50 £278.40per box Supplied to order
Boxes
£0.00 ex VATChoose quantities above

Related products

Rothoblaas Traspir House 135 · Highly breathable membrane
Rothoblaas
1 per box
£88.38ex VAT
£106.06 inc VAT
£88.38 per unit

5–7 days

Loading basket...
— —
Go to checkout
£55.83 DGZ7220 · ex VAT
Need it faster? Email us before you order. We will check whether we can beat our standard lead time on your order, and what that would cost. info@timbasystems.com